This documentation associated wth tlsbindaddr is still useful so lets
synchronize it between trunk and 1.6.x branches.
(issue #17054)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@255066 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Update some confusing documentation for the tlsbindaddr
option in sip.conf.sample. Point at a link instead which
has better documentation.
(closes issue #17054)
Reported by: klaus3000
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@255021 65c4cc65-6c06-0410-ace0-fbb531ad65f3
application is executing on a channel.
This patch addresses an issue found during working with end-users
using res_fax. If an incoming call is answered in the dialplan, or
jumps to the 'fax' extension due to reception of a CNG tone (with
faxdetect enabled), and then the remote endpoint sends a T.38
re-INVITE, it is possible for the channel's T.38 state to be
'T38_STATE_NEGOTIATING' when the application starts up. Unfortunately,
even if the application wants to use T.38, it can't respond to the
peer's negotiation request, because the AST_CONTROL_T38_PARAMETERS
control frame that chan_sip sent originally has been lost, and the
application needs the content of that frame to be able to formulate a
reply.
This patch adds a new 'request' type to AST_CONTROL_T38_PARAMETERS,
AST_T38_REQUEST_PARMS. If the application sends this request, chan_sip
will re-send the original control frame (with
AST_T38_REQUEST_NEGOTIATE as the request type), and the application
can respond as normal. If this occurs within the five second timeout
in chan_sip, the automatic cancellation of the peer reinvite will be
stopped, and the application will 'own' the negotiation process from
that point onwards.
This also improves the code path in chan_sip to allow sip_indicate(),
when called for AST_CONTROL_T38_PARAMETERS, to be able to return a
non-zero response, which should have been in place before since the
control frame *can* fail to be processed properly. It also modifies
ast_indicate() to return whatever result the channel driver returned
for this control frame, rather than converting all non-zero results
into '-1'. Finally, the new request type intentionally returns a
positive value, so that an application that sends
AST_T38_REQUEST_PARMS can know for certain whether the channel driver
accepted it and will be replying with a control frame of its own, or
whether it was ignored (if the sip_indicate()/ast_indicate() path had
properly supported failure responses before, this would not be
necessary).
This patch also modifies res_fax to take advantage of the new request.
In addition, this patch makes sip_t38_abort() actually lock the
private structure before doing its work... bad programmer, no donut.
This patch also enhances chan_sip's 'faxdetect' support to allow
triggering on T.38 re-INVITEs received as well as CNG tone detection.
Review: https://reviewboard.asterisk.org/r/556/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@254450 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This change basically reverts the change reviewed in
https://reviewboard.asterisk.org/r/374/ and instead limits the
updating of the RTP synchronization source to only those times when we
detect that the other side of the conversation has changed the ssrc.
The problem is that SRCUPDATE control frames are sent many times where
we don't want a new ssrc, including whenever Asterisk has to send DTMF
in a normal bridge. This is also not the first time that this mistake
has been made. The initial implementation of the ast_rtp_new_source
function also changed the ssrc--and then it was removed because of
this same issue. Then, we put it back in again to fix a different
issue. This patch attempts to only change the ssrc when we see that
the other side of the conversation has changed the ssrc.
It also renames some functions to make their purpose more clear.
Review: https://reviewboard.asterisk.org/r/540/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@252089 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When configuring the adaptive jitterbuffer, the target_extra
value not only could not be set from the configuration, but was
not even being set to its proper default. This value is required
in order for the adaptive jitterbuffer to work correctly. To resolve
this a config option has been added to expose this value to the conf
files, and a default value is provided when no config specific value
is present.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@249893 65c4cc65-6c06-0410-ace0-fbb531ad65f3
First off, these options weren't actually doing anything.
By the time the options were parsed, the peer and dialog
containers had already been allocated with their default
values.
Second, hash table size is something that doesn't really
make sense to change in a config file. If a user is that
interested in changing the hashtable size, he can modify
the source itself.
I have removed the parsing of the hash_peer, hash_user,
and hash_dialog options. I have removed the hash_user_size
variable altogether since it is not used at all. I also
changed hash_peer_size and hash_dialog_size to be constant,
and have changed the symbols to be in all caps as constants
typically are. I have also removed the entire section in
sip.conf.sample regarding configurable hashtable sizes.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@245192 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Internally the way T.38 is negotiated has changed and the option no longer
reflects a behavior that is valid. It will now look for a CNG tone on
received calls and if present send the call to the 'fax' extension. It is
then up to the application or channel to request the switch over to T.38.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@230881 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Just updating a spelling error and some capitalization in a
documentation update that Olle added. May the Swenglish be
with you.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@229639 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r226382 | lmadsen | 2009-10-28 15:06:13 -0500 (Wed, 28 Oct 2009) | 9 lines
Update documentation in sip.conf.sample.
Update the documentation in sip.conf.sample in order to make it more clear
that directmedia/canreinvite do not cause Asterisk to ignore reINVITEs. It
is only used to stop Asterisk from generating a reINVITE, but does not stop
it from accepting them if necessary.
(closes issue #15644)
Reported by: lmadsen
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@226384 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This change adds a configuration option to SIP peers, unsolicited_mailbox, which
configures a virtual mailbox to use for received new/old MWI information. This
virtual mailbox can then be used by any device supporting MWI.
(closes issue #13028)
Reported by: AsteriskRocks
Patches:
bug_13028_chan_sip_external_mwi_20090707.patch uploaded by cmaj (license 830)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@226060 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is the second commit for this and documents the text stream using the configured
IP address and fixes a bug in the original patch where the UDPTL stream would also
use the different IP address.
(closes issue #14729)
Reported by: _brent_
Patches:
media_address.patch uploaded by brent (license 388)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@225089 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r225032 | dvossel | 2009-10-21 09:37:04 -0500 (Wed, 21 Oct 2009) | 20 lines
IAX/SIP shrinkcallerid option
The shrinking of caller id removes '(', ' ', ')', non-trailing '.',
and '-' from the string. This means values such as 555.5555 and
test-test result in 555555 and testtest. There are instances,
such as Skype integration, where a specific value is passed via
caller id that must be preserved unmodified. This patch makes
the shrinking of caller id optional in chan_sip and chan_iax in
order to support such cases. By default this option is on to
preserve previous expected behavior.
(closes issue #15940)
Reported by: dimas
Patches:
v2-15940.patch uploaded by dimas (license 88)
15940_shrinkcallerid_trunk.c uploaded by dvossel (license 671)
Tested by: dvossel
Review: https://reviewboard.asterisk.org/r/408/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@225033 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for TCP/TLS in the Contact header when using
NAT, specifically externip or externhost. The original issue was that
Asterisk sent 5060 as the port in the contact header whether TLS was
used or not. Additionally, this patch adds 2 config options to sip.conf,
specifically externtcpport and externtlsport. This allows a user to
specify different external ports for TCP and TLS other than those used
internally, this is especially useful in in a PAT/port redirection setup.
Thanks to ebroad for reporting the issue and providing the patch!
(closes issue #15880)
Reported by: ebroad
Patches:
portmap.patch uploaded by ebroad (license 878)
externtXXport_v2.patch uploaded by ebroad (license 878)
Tested by: ebroad
Review: https://reviewboard.asterisk.org/r/392/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222398 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Many T.38 endpoints incorrectly send the maximum IFP frame size they can accept
as the T38FaxMaxDatagram value in their SDP, when in fact this value is
supposed to be the maximum UDPTL payload size (datagram size) they can accept.
If the value they supply is small enough (a commonly supplied value is '72'),
T.38 UDPTL transmissions will likely fail completely because the UDPTL packets
will not have enough room for a primary IFP frame and the redundancy used for
error correction. If this occurs, the Asterisk UDPTL stack will emit log messages
warning that data loss may occur, and that the value may need to be overridden.
This patch extends the 't38pt_udptl' configuration option in sip.conf to allow
the administrator to override the value supplied by the remote endpoint and
supply a value that allows T.38 FAX transmissions to be successful with that
endpoint. In addition, in any SIP call where the override takes effect, a debug
message will be printed to that effect. This patch also removes the
T38FaxMaxDatagram configuration option from udptl.conf.sample, since it has not
actually had any effect for a number of releases.
In addition, this patch cleans up the T.38 documentation in sip.conf.sample
(which incorrectly documented that T.38 support was passthrough only).
(issue #15586)
Reported by: globalnetinc
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222110 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221360 | mnicholson | 2009-09-30 14:36:06 -0500 (Wed, 30 Sep 2009) | 10 lines
Fix SRV lookup and Request-URI generation in chan_sip.
This patch adds a new field "portinuri" to the sip dialog struct and the sip peer struct. That field is used during RURI generation to determine if the port should be included in the RURI. It is also used in some places to determine if an SRV lookup should occur.
(closes issue #14418)
Reported by: klaus3000
Tested by: klaus3000, mnicholson
Review: https://reviewboard.asterisk.org/r/369/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221432 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221086 | twilson | 2009-09-30 09:49:11 -0500 (Wed, 30 Sep 2009) | 25 lines
Change the SSRC by default when our media stream changes
Be default, change SSRC when doing an audio stream changes Asterisk doesn't
honor marker bit when reinvited to already-bridged RTP streams,resulting in
far-end stack discarding packets with "old" timestamps that areactually part of
a new stream. This patch sends AST_CONTROL_SRCUPDATE whenever there is a
reinvite, unless the 'constantssrc' is set to true in sip.conf.
The original issue reported to Digium support detailed the following situation:
ITSP <-> Asterisk 1.4.26.2 <-> SIP-based Application Server Call comes in
fromITSP, Asterisk dials the app server which sends a re-invite back
toAsterisk--not to negotiate to send media directly to the ITSP, but to
indicatethat it's changing the stream it's sending to Asterisk. The app
servergenerates a new SSRC, sequence numbers, timestamps, and sets the marker
bit on the new stream. Asterisk passes through the teimstamp of the new stream,
butdoes not reset the SSRC, sequence numbers, or set the marker bit.
When the timestamp on the new stream is older than the timestamp on the
originalstream, the ITSP (which doesn't know there has been any change) discards
the newframes because it thinks they are too old. This patch addresses this by
changing the SSRC on a stream update unless constantssrc=true is set in
sip.conf.
Review: https://reviewboard.asterisk.org/r/374/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221266 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r216430 | oej | 2009-09-04 15:45:48 +0200 (Fre, 04 Sep 2009) | 27 lines
Make apps send PROGRESS control frame for early media and fix too early media issue in SIP
The issue at hand is that some legacy (dying) PBX systems send empty media frames on PRI
links *before* any call progress. The SIP channel receives these frames and by default
signals 183 Session progress and starts sending media. This will cause phones to
play silence and ignore the later 180 ringing message. A bad user experience.
The fix is twofold:
- We discovered that asterisk apps that support early media ("noanswer") did not send
any PROGRESS frame to indicate early media. Fixed.
- We introduce a setting in chan_sip so that users can disable any relay of media frames
before the outbound channel actually indicates any sort of call progress.
In 1.4, 1.6.0 and 1.6.1, this will be disabled for backward compatibility. In later versions
of Asterisk, this will be enabled. We don't assume that it will change your Asterisk
phone experience - only for the better.
We encourage third-party application developers to make sure that if they have applications
that wants to send early media, add a PROGRESS control frame transmission to make sure that
all channel drivers actually will start sending early media. This has not been the default
in Asterisk previous to this patch, so if you got inspiration from our code, you need to
update accordingly. Sorry for the trouble and thanks for your support.
This code has been running for a few months in a large scale installation (over 250
servers with PRI and/or BRI links to old PBX systems).
That's no proof that this is an excellent patch, but, well, it's tested :-)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@216438 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Allows characters that are otherwise used as delimiters to be used within
certain fields (like the secret).
(closes issue #15008, closes issue #15672)
Reported by: tilghman
Patches:
20090818__issue15008.diff.txt uploaded by tilghman (license 14)
Tested by: lmadsen, tilghman
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@213098 65c4cc65-6c06-0410-ace0-fbb531ad65f3
It is clear from multiple mailing list, forum, wiki and other sorts of posts
that users don't really understand the effects that the 'canreinvite' config
option actually has, and that in some cases they think that setting it to 'no'
will actually cause various other features (T.38, MOH, etc.) to not work properly,
when in fact this is not the case. This patch changes the proper name of the
option to what it should have been from the beginning ('directmedia'), but
preserves backwards compatibility for existing configurations.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@210190 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Let's try that again, this time removing trailing whitespace and not leading
whitespace. I can't believe no one noticed.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@197535 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In sip.conf the transport option allows for the configuration of what transport types (udp, tcp, and tls) a peer will accept, but only the first type listed was used for outbound connections. This patch changes this. Now the default transport type is only used until the peer registers. When registration takes place the transport type is parsed out of the Contact header. If the Contact header's transport type is equal to one that the peer supports, the peer's default transport type for outbound connections is set to match the Contact header's type. If the Contact header's transport type is not present, then the peer's default transport type is set to match the one the peer registered with. When a peer unregisters or the registration expires, the default transport type for that peer is reset.
(closes issue #12282)
Reported by: rjain
Patches:
reg_patch_1.diff uploaded by dvossel (license 671)
Tested by: dvossel
(closes issue #14727)
Reported by: pj
Patches:
reg_patch_3.diff uploaded by dvossel (license 671)
Tested by: pj, dvossel
Review: https://reviewboard.asterisk.org/r/249/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196416 65c4cc65-6c06-0410-ace0-fbb531ad65f3
SIP purists may want to look the other way...
When COLP/CONP support for SIP was committed, there was a condition under
which Asterisk may transmit a SIP UPDATE in order to communicate the change
in connected line information. The issue here is that while we could send a
SIP UPDATE message, we were not prepared to receive such an UPDATE and would
always responde with a 501 when we received an UPDATE.
The situation was a bit rough. We really want to be able to receive UPDATEs
having to do with connected line changes, but the amount of effort involved
in properly supporting RFC 3311 was staggering. This commit represents a
compromise.
First, it was decided that it is important to only send a SIP UPDATE to
an endpoint that is able to handle one. So, now we have added parsing of
the Allow header into SIP. We store the allowed methods on SIP peers so
that when we communicate with them, we already will know what we can and
cannot send to them. We will parse the peer's allowed methods when he registers
with us. If the peer is not the type to register with us, but the qualify option
is enabled, then we will use the response to the OPTIONS request we send
the peer to determine the peer's allowed methods. When the peer's registration
expires, or when qualify deems the peer to be unreachable, we clear the allowed
methods from the peer.
For an actual call, we will copy the peer's allowed methods to the sip_pvt
representing the call leg. If we are communicating with an endpoint which is
not a peer, then we will just parse the Allow header from the first message
we receive during the call and store the information in the sip_pvt.
If, during communication with a peer, we receive a 501 response, then we will
make sure to save the fact that we cannot use that method when communicating
with that peer.
Now, with all that infrastructure in place, the only actual place we use this
information currently is when attempting to send a connected line change using
an UPDATE request. If we cannot send the change immediately using an UPDATE,
we will set the SIP_NEEDREINVITE flag so that we can send a REINVITE as soon
as it is allowed.
The second part of the changes here is for Asterisk to accept UPDATE requests
that have connected line changes. Since we are not fully supporting RFC 3311,
Asterisk will NOT place the UPDATE method in Allow headers it sends. Instead,
if you are communicating with what you know to be another Asterisk box, you may
set the rpid_update parameter in sip.conf so that we will send UPDATEs to that
Asterisk box. When we send a connected line update, we set a custom header
called "X-Asterisk-rpid-update."
On the receiving end, if Asterisk receives an UPDATE that does not have the
"X-Asterisk-rpid-update" header present, then Asterisk will respond with a 501
since media-changing UPDATEs are not supported. We should never get such
UPDATEs, since as was stated earlier, Asterisk does not put UPDATE in its Allow
header. If the custom header is present in the received UPDATE, though, then we
will check the incoming request for connected line updates and queue the update
on the channel where the change occurred.
ABE-1840
ABE-1822
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@195589 65c4cc65-6c06-0410-ace0-fbb531ad65f3
chan_sip allows for outbound TLS connections, but does not allow the user to specify what protocol to use (default was SSLv2, and still is if this new option is not specified). This patch lets the user pick the SSL/TLS client method for outbound connections in sip.
(closes issue #14770)
Reported by: TheOldSaint
(closes issue #14768)
Reported by: TheOldSaint
Review: http://reviewboard.digium.com/r/240/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191177 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Adds option to specify a private key .pem file when configuring TLS or SSL in AMI, HTTP, and SIP. Before this, the certificate file was used for both the public and private key. It is possible for this file to hold both, but most configurations allow for a separate private key file to be specified. Clarified in .conf files how these options are to be used. The current conf files do not explain how the private key is handled at all, so without knowledge of Asterisk's TLS implementation, it would be hard to know for sure what was going on or how to set it up.
Review: http://reviewboard.digium.com/r/234/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@190545 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This allows for you to change the From header for outgoing MWI
NOTIFY requests. Prior to this, the best you could do was to
set a callerid in the general section of sip.conf. The problem
was that this was used for all outbound requests, not just
MWI NOTIFY requests.
AST-201
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@187560 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The channel drivers which have been most heavily tested with these enhancements are
chan_sip and chan_misdn. Further work is being done to add Q.SIG support and will be
introduced in a later commit. chan_skinny has code added to it here, but according
to user pj, the support on chan_skinny is not working as of now. This will be fixed in
a later commit.
A special thanks goes out to bugtracker user gareth for getting the ball rolling and
providing the initial support for this work. Without his initial work on this, this would
not have been nearly as painless as it was.
This functionality has been tested by Digium's product quality department, as well as a
customer site running thousands of calls every day. In addition, many many many many bugtracker
users have tested this, too.
(closes issue #8824)
Reported by: gareth
Review: http://reviewboard.digium.com/r/201
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186525 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This API provides a generic way for multiple RTP stacks to be
integrated into Asterisk. Right now there is only one present, res_rtp_asterisk,
which is the existing Asterisk RTP stack. Functionality wise this commit
performs the same as previously. API documentation can be viewed in the
rtp_engine.h header file.
Review: http://reviewboard.digium.com/r/209/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186078 65c4cc65-6c06-0410-ace0-fbb531ad65f3
