The PRI and SS7 link control threads are not stopped correctly when the
chan_dahdi.so module is unloaded. The link control threads pri_dchannel()
and ss7_linkset() are not awakened from a poll() to cancel the thread.
* Added a SIGURG signal after requesting the thread cancel to break the
link control thread poll() immediately.
For SS7 it was slightly worse, the link poll() timeout would always be
whatever was the last libss7 scheduled event time used. If no libss7
scheduled event was pending, the thread could run more often than
necessary.
* Set nextms to 60 seconds for the ss7_linkset() poll() if there is no
other libss7 scheduled event.
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@399818 65c4cc65-6c06-0410-ace0-fbb531ad65f3
If a SS7 call comes in requesting a CIC that is in-alarm, the call is
accepted and connects if the extension exists in the dialplan. The call
does not have any audio.
* Made release the call immediately with circuit congestion cause.
(closes issue ASTERISK-20204)
Reported by: Tuan Le
Patches:
jira_asterisk_20204_v1.8.patch (license #5621) patch uploaded by rmudgett
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@376058 65c4cc65-6c06-0410-ace0-fbb531ad65f3
For SS7, the companding law for a call was chosen inconsistently depending
upon ss7type (ITU vs ANSI) and the DAHDI companding default (T1 vs E1).
For incoming calls, the companding law was determined by ss7type. For
outgoing calls, the companding law was determined by the DAHDI default.
With the wrong combination you would get A-law/u-law conflicts. An
A-law/u-law conflict sounds like bad static on the line.
SS7 ITU signaling with E1 line: ok
SS7 ITU signaling with T1 line: noise
SS7 ANSI signaling with E1 line: noise
SS7 ANSI signaling with T1 line: ok
* Fix the companding law used to be determined by the SS7 signaling type
only.
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@373090 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Since we now have tools that scan through the source tree looking for files
with specific support levels, we need to ensure that every file that is
a component of a 'core' or 'extended' module (or the main Asterisk binary)
is explicitly marked with its support level. This patch adds support-level
indications to many more source files in tree, but avoids adding them to
third-party libraries that are included in the tree and to source files
that don't end up involved in Asterisk itself.
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@369001 65c4cc65-6c06-0410-ace0-fbb531ad65f3
SS7 is a trunk protocol and should clear a failed call as soon as
possible.
* Made SS7 hangup a call immediately if it has not connected yet for
INCOMPLETE/BUSY/CONGESTION causes. Otherwise, play an appropriate inband
tone.
(closes issue ASTERISK-19372)
Reported by: Igor Nikolaev
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@358278 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Outgoing SS7 calls fail to detect incoming DTMF so any bridged channel
that requires out-of-band DTMF will not work.
* Added sig_ss7_open_media() calls at appropriate places in sig_ss7.c.
The new call converts conditionaled out unconverted code and shows that
the code really did something useful.
* Improved some chan_dahdi DTMF debug messages to help track DTMF
handling.
(closes issue ASTERISK-19312)
Reported by: Igor Nikolaev
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@358260 65c4cc65-6c06-0410-ace0-fbb531ad65f3
'p->outgoing' in chan_dahdi and sig_analog wern't kept in sync, particulary FXS ast_hangup didn't clear the 'outgoing' flag.
sig_pri and sig_ss7 were keeping 'outgoing' flag insync.
Now provides a callback for all the low level sig_XXX modules.
(issue ASTERISK-19316)
alecdavis (license 585)
Reported by: Jeremy Pepper
Tested by: alecdavis
Review: https://reviewboard.asterisk.org/r/1747/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@355850 65c4cc65-6c06-0410-ace0-fbb531ad65f3
* Added a CLI "ss7 show channels" command that might prove useful for
future debugging.
* Made the incoming SS7 channel event check and gripe message uniform.
* Made sure that the DNID string for an incoming call is always
initialized.
(issue ASTERISK-17966)
Reported by: Kenneth Van Velthoven
Patches:
jira_asterisk_17966_v1.8_glare.patch (license #5621) patch uploaded by rmudgett
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@340365 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Fixes the crash in ASTERISK-17955 gdb-11918.txt backtrace.
* Added some missing libss7 access lock protection.
* Prevent cancelling the ss7_linkset() thread at inoportune times just
like the pri_dchannel() thread.
(issue ASTERISK-17955)
Reported by: Ian M Sherman
Patches:
jira_asterisk_17955_v1.8.patch (license #5621) patch uploaded by rmudgett
(attached to related ASTERISK-17966)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@337007 65c4cc65-6c06-0410-ace0-fbb531ad65f3
sig_ss7_hangup() failed to release the SS7 linkset lock if the call had
the alreadyhungup flag set.
* Made unlock the SS7 linkset lock in sig_ss7_hangup() if the
alreadyhungup flag is set.
* Made ss7_start_call() not hold any locks while creating the channel for
an incoming call to prevent deadlock.
* Made ss7_grab() a void function, since it could never fail, to simplify
calling code.
* Made obtain the channel lock to do softhangup in some places.
Patches:
jira_ast_668_v1.8.patch (license #5621) patch uploaded by rmudgett
JIRA AST-668
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@336977 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a SIP phone uses the dial application and receives a 484 Address
Incomplete response, if overlapped dialing is enabled for SIP, then
the 484 Address Incomplete is forwarded back to the SIP phone and the
HANGUPCAUSE channel variable is set to 28. Previously, the Incomplete
application dialplan logic was automatically triggered; now, explicit
dialplan usage of the application is required.
Additionally, this patch adds a new AST_CONTOL_FRAME type called
AST_CONTROL_INCOMPLETE. If a channel driver receives this control frame,
it is an indication that the dialplan expects more digits back from the
device. If the device supports overlap dialing it should attempt to
notify the device that the dialplan is waiting for more digits; otherwise,
it can handle the frame in a manner appropriate to the channel driver.
(closes issue ASTERISK-17288)
Reported by: Mikael Carlsson
Tested by: Matthew Jordan
Review: https://reviewboard.asterisk.org/r/1416/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@335064 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The channel state is not updated to RINGING when an ALERTING message is
received. Regression caused when sig_pri.c (also sig_ss7.c) extracted
from chan_dahdi.c.
* Added missing channel state update to RINGING when the
AST_CONTROL_RINGING frame is queued for ISDN and SS7.
(closes issue #19257)
Reported by: alecdavis
Patches:
issue19257_v1.8_v2.patch uploaded by rmudgett (license 664)
Tested by: alecdavis, rmudgett
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@318499 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.6.2
................
r303769 | rmudgett | 2011-01-25 11:42:42 -0600 (Tue, 25 Jan 2011) | 47 lines
Merged revisions 303765 via svnmerge from
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r303765 | rmudgett | 2011-01-25 11:36:50 -0600 (Tue, 25 Jan 2011) | 40 lines
Sending out unnecessary PROCEEDING messages breaks overlap dialing.
Issue #16789 was a good idea. Unfortunately, it breaks overlap dialing
through Asterisk. There is not enough information available at this point
to know if dialing is complete. The ast_exists_extension(),
ast_matchmore_extension(), and ast_canmatch_extension() calls are not
adequate to detect a dial through extension pattern of "_9!".
Workaround is to use the dialplan Proceeding() application early in
non-dial through extensions.
* Effectively revert issue #16789.
* Allow outgoing overlap dialing to hear dialtone and other early media.
A PROGRESS "inband-information is now available" message is now sent after
the SETUP_ACKNOWLEDGE message for non-digital calls. An
AST_CONTROL_PROGRESS is now generated for incoming SETUP_ACKNOWLEDGE
messages for non-digital calls.
* Handling of the AST_CONTROL_CONGESTION in chan_dahdi/sig_pri was
inconsistent with the cause codes.
* Added better protection from sending out of sequence messages by
combining several flags into a single enum value representing call
progress level.
* Added diagnostic messages for deferred overlap digits handling corner
cases.
(closes issue #17085)
Reported by: shawkris
(closes issue #18509)
Reported by: wimpy
Patches:
issue18509_early_media_v1.8_v3.patch uploaded by rmudgett (license 664)
Expanded upon issue18509_early_media_v1.8_v3.patch to include analog
and SS7 because of backporting requirements.
Tested by: wimpy, rmudgett
........
................
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.8@303771 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The purpose of this patch is to eliminate struct ast_callerid since it has
turned into a miscellaneous collection of various party information.
Eliminate struct ast_callerid and replace it with the following struct
organization:
struct ast_party_name {
char *str;
int char_set;
int presentation;
unsigned char valid;
};
struct ast_party_number {
char *str;
int plan;
int presentation;
unsigned char valid;
};
struct ast_party_subaddress {
char *str;
int type;
unsigned char odd_even_indicator;
unsigned char valid;
};
struct ast_party_id {
struct ast_party_name name;
struct ast_party_number number;
struct ast_party_subaddress subaddress;
char *tag;
};
struct ast_party_dialed {
struct {
char *str;
int plan;
} number;
struct ast_party_subaddress subaddress;
int transit_network_select;
};
struct ast_party_caller {
struct ast_party_id id;
char *ani;
int ani2;
};
The new organization adds some new information as well.
* The party name and number now have their own presentation value that can
be manipulated independently. ISDN supplies the presentation value for
the name and number at different times with the possibility that they
could be different.
* The party name and number now have a valid flag. Before this change the
name or number string could be empty if the presentation were restricted.
Most channel drivers assume that the name or number is then simply not
available instead of indicating that the name or number was restricted.
* The party name now has a character set value. SIP and Q.SIG have the
ability to indicate what character set a name string is using so it could
be presented properly.
* The dialed party now has a numbering plan value that could be useful to
have available.
The various channel drivers will need to be updated to support the new
core features as needed. They have simply been converted to supply
current functionality at this time.
The following items of note were either corrected or enhanced:
* The CONNECTEDLINE() and REDIRECTING() dialplan functions were
consolidated into func_callerid.c to share party id handling code.
* CALLERPRES() is now deprecated because the name and number have their
own presentation values.
* Fixed app_alarmreceiver.c write_metadata(). The workstring[] could
contain garbage. It also can only contain the caller id number so using
ast_callerid_parse() on it is silly. There was also a typo in the
CALLERNAME if test.
* Fixed app_rpt.c using ast_callerid_parse() on the channel's caller id
number string. ast_callerid_parse() alters the given buffer which in this
case is the channel's caller id number string. Then using
ast_shrink_phone_number() could alter it even more.
* Fixed caller ID name and number memory leak in chan_usbradio.c.
* Fixed uninitialized char arrays cid_num[] and cid_name[] in
sig_analog.c.
* Protected access to a caller channel with lock in chan_sip.c.
* Clarified intent of code in app_meetme.c sla_ring_station() and
dial_trunk(). Also made save all caller ID data instead of just the name
and number strings.
* Simplified cdr.c set_one_cid(). It hand coded the ast_callerid_merge()
function.
* Corrected some weirdness with app_privacy.c's use of caller
presentation.
Review: https://reviewboard.asterisk.org/r/702/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@276347 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Extract the SS7 specific code out of chan_dahdi like what was done to
ISDN/PRI and analog signaling. The new SS7 structures were modeled on
sig_pri.
The changes to sig_pri are an enhancement and a bug fix made possible
because SS7 was extracted.
1) The sig_pri TRANSFERCAPABILITY channel variable should have been set
unconditionally in sig_pri_new_ast_channel().
2) SS7/PRI transfer capability interaction in dahdi_new() fixed because of
SS7 extraction.
3) Module ref count error in dahdi_new() if startpbx failed to start the
PBX for some reason.
Review: https://reviewboard.asterisk.org/r/661/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@268774 65c4cc65-6c06-0410-ace0-fbb531ad65f3
