With tls and udp enabled asterisk generates a warning about sending
message via udp instead of tls.
sip notify command via cli works as expected and without warning.
asterisk has to set the connection information accordingly to connection
and not on presumption
ASTERISK-28057 #close
Change-Id: Ib43315aba1f2c14ba077b52d8c5b00be0006656e
As they're not actively used, they only grow stale. The moduleinfo field itself
is kept in Asterisk 13/15 for ABI compatibility.
ASTERISK-28046 #close
Change-Id: I8df66a7007f807840414bb348511a8c14c05a9fc
Also remove function peer_ipcmp_cb since it's not used (according to
rmudgett).
Prior to b2c4e8660a (ASTERISK_27457)
insecure=port was the defacto standard. That commit also prevented
insecure=port from being applied for sip/tcp or sip/tls.
Into consideration there are three sets of behaviour:
1. "previous" - before the above commit.
2. "current" - post above commit, pre this one.
3. "new" - post this commit.
The problem that the above commit tried to address was guests over TCP.
It succeeded in doing that but broke transport!=udp with host!=dynamic.
This commit attempts to restore sane behaviour with respect to
transport!=udp for host!=dynamic whilst still retaining the guest users
over tcp.
It should be noted that when looking for a peer, two passes are made, the
first pass doesn't have SIP_INSECURE_PORT set for the searched-for peer,
thus looking for full matches (IP + Port), the second pass sets
SIP_INSECURE_PORT, thus expecting matches on IP only where the matched
peer allows for that (in the author's opinion: UDP with insecure=port,
or any TCP based, non-dynamic host).
In previous behaviour there was special handling for transport=tcp|tls
whereby a peer would match during the first pass if the utilized
transport was TCP|TLS (and the peer allowed that specific transport).
This behaviour was wrong, or dubious at best. Consider two dynamic tcp
peers, both registering from the same IP (NAT), in this case either peer
could match for connections from an IP. It's also this behaviour that
prevented SIP guests over tcp.
The above referenced commit removed this behaviour, but kept applying
the SIP_INSECURE_PORT only to WS|WSS|UDP. Since WS and WSS is also TCP
based, the logic here should fall into the TCP category.
This patch updates things such that the previously non-explicit (TCP
behaviour) transport test gets performed explicitly (ie, matched peer
must allow for the used transport), as well as the indeterministic
source-port nature of the TCP protocol is taken into account. The new
match algorithm now looks like:
1. As per previous behaviour, IP address is matched first.
2. Explicit filter with respect to transport protocol, previous
behaviour was semi-implied in the test for TCP pure IP match - this now
made explicit.
3. During first pass (without SIP_INSECURE_PORT), always match on port.
4. If doing UDP, match if matched against peer also has
SIP_INSECURE_PORT, else don't match.
5. Match if not a dynamic host (for non-UDP protocols)
6. Don't match if this is WS|WSS, or we can't trust the Contact address
(presumably due to NAT)
7. Match (we have a valid Contact thus if the IP matches we have no
choice, this will likely only apply to non-NAT).
To logic-test this we need a few different scenarios. Towards this end,
I work with a set number of peers defined in sip.conf:
[peer1]
host=1.1.1.1
transport=tcp
[peer2]
host=1.1.1.1
transport=udp
[peer3]
host=1.1.1.1
port=5061
insecure=port
transport=udp
[peer4]
host=1.1.1.2
transport=udp,tcp
[peer5]
host=dynamic
transport=udp,tcp
Test cases for UDP:
1 - incoming UDP request from 1.1.1.1:
- previous:
- pass 1:
* peer1 or peer2 if from port 5060 (indeterminate, depends on peer
ordering)
* peer3 if from port 5061
* peer5 if registered from 1.1.1.1 and source port matches
- pass 2:
* peer3
- current: as per previous.
- new:
- pass 1:
* peer2 if from port 5060
* peer3 if from port 5061
* peer5 if registered from 1.1.1.1 and source port matches
- pass 2:
* peer3
2 - incoming UDP request from 1.1.1.2:
- previous:
- pass 1:
* peer5 if registered from 1.1.1.2 and port matches
* peer4 if source port is 5060
- pass 2:
* no match (guest)
- current: as previous.
- new as previous (with the variation that if peer5 didn't have udp as
allowed transport it would not match peer5 whereas previous
and current code could).
3 - incoming UDP request from anywhere else:
- previous:
- pass 1:
* peer5 if registered from that address and source port matches.
- pass 2:
* peer5 if insecure=port is additionally set.
* no match (guest)
- current - as per previous
- new - as per previous
Test cases for TCP based transports:
4 - incoming TCP request from 1.1.1.1
- previous:
- pass 1 (indeterministic, depends on ordering of peers in memory):
* peer1; or
* peer5 if peer5 registered from 1.1.1.1 (irrespective of source port); or
* peer2 if the source port happens to be 5060; or
* peer3 if the source port happens to be 5061.
- pass 2: cannot happen since pass 1 will always find a peer.
- current:
- pass 1:
* peer1 or peer2 if from source port 5060
* peer3 if from source port 5060
* peer5 if registered as 1.1.1.1 and source port matches
- pass 2:
* no match (guest)
- new:
- pass 1:
* peer 1 if from port 5060
* peer 5 if registered and source port matches
- pass 2:
* peer 1
5 - incoming TCP request from 1.1.1.2
- previous (indeterminate, depends on ordering):
- pass 1:
* peer4; or
* peer5 if peer5 registered from 1.1.1.2
- pass 2: cannot happen since pass 1 will always find a peer.
- current:
- pass 1:
* peer4 if source port is 5060
* peer5 if peer5 registered as 1.1.1.2 and source port matches
- pass 2:
* no match (guest).
- new:
- pass 1:
* peer4 if source port is 5060
* peer5 if peer5 registered as 1.1.1.2 and source port matches
- pass 2:
* peer4
6 - incoming TCP request from anywhere else:
- previous:
- pass 1:
* peer5 if registered from that address
- pass 2: cannot happen since pass 1 will always find a peer.
- current:
- pass 1:
* peer5 if registered from that address and port matches.
- pass 2:
* no match (guest)
- new: as per current.
It should be noted the test cases don't make explicit mention of TLS, WS
or WSS. WS and WSS previously followed UDP semantics, they will now
enforce source port matching. TLS follow TCP semantics.
The previous commit specifically tried to address test-case 6, but broke
test-cases 4 and 5 in the process.
ASTERISK-27881 #close
Change-Id: I61a9804e4feba9c7224c481f7a10bf7eb7c7f2a2
Otherwise console output
(get_refer_info): mutex 'peer' freed more times than we've locked!
(get_refer_info): Error releasing mutex: Operation not permitted
or
(get_refer_info): attempted unlock mutex 'peer' without owning it!
(__ast_read): 'peer' was locked here.
...dump_backtrace
(get_refer_info): Error releasing mutex: Operation not permitted
(__ast_read): mutex 'chan' freed more times than we've locked!
ASTERISK-28011 #close
Change-Id: I6e45f2764ba4f3273a943300f91ac9b461ac2893
This fixes build warnings found by GCC 8. In some cases format
truncation is intentional so the warning is just suppressed.
ASTERISK-27824 #close
Change-Id: I724f146cbddba8b86619d4c4a9931ee877995c84
There is a problem when an INVITE-with-Replaces transfer targets a channel
in a ConfBridge. The transfer will unconditionally swap out the
ConfBridge channel. Unfortunately, the ConfBridge state will not be aware
of this change. Unexpected behavior will happen as a result since
ConfBridge channels currently can only be replaced by a masquerade and not
normal bridge channel moves.
* We just need to pretend that the channel isn't in a bridge (like other
transfer methods already do) so the transfer channel will masquerade into
the ConfBridge channel.
Change-Id: I209beb0e748fa4f4b92a576f36afa8f495ba4c82
Given the below call scenario:
A -> Ast1 -> B
C <- Ast2 <- B
1) A calls B through Ast1
2) B calls C through Ast2
3) B transfers A to C
When party B transfers A to C, B sends a REFER to Ast1 causing Ast1 to
send an INVITE with replaces to Ast2. Ast2 then leaks a channel ref of
the channel between Ast1 and Ast2.
Channel ref leaks are easily seen in the CLI "core show channels" output.
The leaked channels appear in the output but you can do nothing with them
and they never go away unless you restart Asterisk.
* Properly account for the channel refs when imparting a channel into a
bridge when handling an INVITE with replaces in handle_invite_replaces().
The ast_bridge_impart() function steals a channel ref but the code didn't
account for how many refs were held by the code at the time and which ref
was stolen.
* Eliminated RAII_VAR in handle_invite_replaces().
ASTERISK-27740
Change-Id: I7edbed774314b55acf0067b2762bfe984ecaa9a4
Checking option_debug directly is incorrect as it ignores file/module
specific debug settings. This system-wide change replaces nearly all
direct checks for option_debug with the DEBUG_ATLEAST macro.
Change-Id: Ic342d4799a945dbc40ac085ac142681094a4ebf0
The "ptime" SDP parameter received in a SIP response was not honoured.
Moreover, in the abscence of this "ptime" parameter, locally configured
framing was lost during response processing.
This patch systematically stores the framing information in the
ast_rtp_codecs structure, taking it from the response or from the
configuration as appropriate.
ASTERISK-27674
Change-Id: I828a6a98d27a45a8afd07236a2bd0aa3cbd3fb2c
When constructing a dialog-info+xml NOTIFY message a ringing channel
is found if the state is ringing and further information is placed into
the message. Due to the migration to the Stasis message bus this did
not always work as expected.
This change raises a second ringing event in such a way to guarantee
that the event is received by chan_sip and another lookup is done to
find the ringing channel.
ASTERISK-24488
Change-Id: I547a458fc59721c918cb48be060cbfc3c88bcf9c
Check if initreq data string exists before using it when processing a
CANCEL request.
ASTERISK-27666
Change-Id: Id1d0f0fa4ec94e81b332b2973d93e5a14bb4cc97
A patch for sending in-dialog SIP NOTIFY message
with "SIPnotify" AMI action.
ASTERISK-27461
(created patch for 13 branch manually due to merge conflict)
Change-Id: I255067f02e2ce22c4b244f12134b9a48d210c22a
Per RFC 5245, the foundation specified with an ICE candidate can be up
to 32 characters but we are only allowing for 31.
ASTERISK-27498 #close
Reported by: Michele Prà
Change-Id: I05ce7a5952721a76a2b4c90366168022558dc7cf
Fix instances of:
* Retreive
* Recieve
* other then
* different then
* Repeated words ("the the", "an an", "and and", etc).
* othterwise, teh
ASTERISK-24198 #close
Change-Id: I3809a9c113b92fd9d0d9f9bac98e9c66dc8b2d31
In change_redirecting_information variables we use ast_strlen_zero to
see if a value should be saved. In the case where the value is not NULL
but is a zero length string we leaked.
handle_response_subscribe leaked a reference to the ccss monitor
instance.
Change-Id: Ib11444de69c3d5b2360a88ba2feb54d2c2e9f05f
Log a message to security events when an INVITE is received to an
invalid extension.
ASTERISK-25869 #close
Change-Id: I0da40cd7c2206c825c2f0d4e172275df331fcc8f
Stripping the DNID in a SIP dial string can result in attempting to call
the argument parsing macros on an empty string, causing a crash.
ASTERISK-26131 #close
Reported by: Dwayne Hubbard
Patches:
dw-asterisk-master-dnid-crash.patch (license #6257) patch
uploaded by Dwayne Hubbard
Change-Id: Ib84c1f740a9ec0539d582b09d847fc85ddca1c5e
There are many places in the code base where we ignore the return value
of fcntl() when getting/setting file descriptior flags. This patch
introduces a convenience function that allows setting or clearing file
descriptor flags and will also log an error on failure for later
analysis.
Change-Id: I8b81901e1b1bd537ca632567cdb408931c6eded7
Previously, peers connected via TCP (or TLS) were matched by ignoring their
source port. One cannot say anything when protocol:IP:port match, yes (see
<http://stackoverflow.com/q/3329641>). However, when the ports do not match, the
peers do not match as well.
This change allows two peers connected to an Asterisk server via TCP (or TLS)
behind a NAT (= same source IP address) to be differentiated via their port as
well.
ASTERISK-27457
Reported by: Stephane Chazelas
Change-Id: Id190428bf1d931f2dbfd4b293f53ff8f20d98efa
When chan_sip receives a SUBSCRIBE request with no "Expires" header it
processes the request as an unsubscribe. This is incorrect, per RFC3264
when the "Expires" header is missing a default expiry should be used.
ASTERISK-18140
Change-Id: Ibf6dcd4fdd07a32c2bc38be1dd557981f08188b5
When sip.conf contains 'sipdebug=yes' it is impossible to disable it
using CLI 'sip set debug off'. This corrects the output of that CLI
command to instruct the user to turn sipdebug off in the configuration
file.
ASTERISK-23462 #close
Change-Id: I1cceade9caa9578e1b060feb832e3495ef5ad318
Currently privacy requests are only granted if the Privacy header
value is exactly "id" (defined in RFC 3325). It ignores any other
possible value (or a combination there of). This patch reverses the
logic from testing for "id" to grant privacy, to testing for "none" and
granting privacy for any other value. "none" must not be used in
combination with any other value (RFC 3323 section 4.2).
ASTERISK-27284 #close
Change-Id: If438a21f31a962da32d7a33ff33bdeb1e776fe56
In handle_request_invite, when processing a pickup, a call
is made to get_sip_pvt_from_replaces to locate the pvt for
the subscription. The pvt is assumed to be valid when zero
is returned indicating no error, and is dereferenced which
can cause a crash if it was not found.
This change checks the not found case and returns -1 which
allows the calling code to fail appropriately.
ASTERISK-27217 #close
Reported-by: Bryan Walters
Change-Id: I6bee92b8b8b85fcac3fd66f8c00ab18bc1765612
If directmedia=yes is configured, when call is answered, Asterisk sends reINVITE
to both parties to set up media path directly between the endpoints.
In this reINVITE msg SDP origin line (o=) contains IP address of endpoint
instead of IP of asterisk. This behavior violates RFC3264, sec 8:
"When issuing an offer that modifies the session,
the "o=" line of the new SDP MUST be identical to that in the
previous SDP, except that the version in the origin field MUST
increment by one from the previous SDP."
This patch assures IP address of Asterisk is always sent in
SDP origin line.
ASTERISK-17540
Reported by: saghul
Change-Id: I533a047490c43dcff32eeca8378b2ba02345b64e
GCC 7 has added capability to produce warnings, this fixes most of those
warnings. The specific warnings are disabled in a few places:
* app_voicemail.c: truncation of paths more than 4096 chars in many places.
* chan_mgcp.c: callid truncated to 80 chars.
* cdr.c: two userfields are combined to cdr copy, fix would break ABI.
* tcptls.c: ignore use of deprecated method SSLv3_client_method().
ASTERISK-27156 #close
Change-Id: I65f280e7d3cfad279d16f41823a4d6fddcbc4c88
When sip.conf contained tcpenable=yes and autodomain=yes, the TCP domain was
added in any case, because of a local Boolean-negation error of the return value
of ast_sockaddr_cmp. After fixing this error for TCP and TLS, the TLS domain was
still always added with tlsenable=yes, because the domains were not compared
just on the address but also on the port – and TLS is always on a different port
than UDP/TCP.
ASTERISK-27106
Change-Id: I14fe9e319e238320b094016980445ef3a5b3337c
Because of a copy-and-paste error when the struct ast_sockaddr changed,
tlsbindaddr was not added, when sip.conf contained autodomain=yes; see
"show sip domains" on the command-line interface (CLI) of Asterisk.
ASTERISK-27106
Change-Id: I3d0957150017c223136968ef1266f275d0d6695e
If we are offered or are offering RTCP-MUX, don't consider RTCP ICE
candidates. This confuses certain browsers (current Firefox for
example) and causes intial audio setup delays.
ASTERISK-26982 #close
Change-Id: Ifeaf47e83972fe8dbe58b7fb3d6d1823400cfb91
For outgoing TCP connections, Asterisk uses the first IP address of the
interface instead of the IP address we asked him to bind to.
ASTERISK-26922 #close
Reported-by: Ksenia
Change-Id: I43c71ca89211dbf1838e5bcdb9be8d06d98e54eb
Some equipments may send a re-INVITE containing an SDP in the final ACK
request. If this happens in the context of direct media, the remote end
should be updated with a re-INVITE.
This patch queues an "update RTP peer" frame to trigger the re-INVITE,
instead of the "source change" frame wich was used previously.
ASTERISK-26951
Change-Id: I3644d2025f20e086ea9f8f62b486172c52b5b2e6
In all non-pbx modules, AST_MODULE_LOAD_FAILURE has been changed
to AST_MODULE_LOAD_DECLINE. This prevents asterisk from exiting
if a module can't be loaded. If the user wishes to retain the
FAILURE behavior for a specific module, they can use the "require"
or "preload-require" keyword in modules.conf.
A new API was added to logger: ast_is_logger_initialized(). This
allows asterisk.c/check_init() to print to the error log once the
logger subsystem is ready instead of just to stdout. If something
does fail before the logger is initialized, we now print to stderr
instead of stdout.
Change-Id: I5f4b50623d9b5a6cb7c5624a8c5c1274c13b2b25
SIP user-agents indicate which protocol extensions are allowed in headers
like Supported and Required. Such protocol extensions are Session Timers
(RFC 4028) for example. Session Timers are supported since Mantis-10665.
Since ASTERISK-21721, not only the first but multiple Supported/Required
headers in a message are parsed. In that change, an existing variable was
re-used within a newly added do-loop. Currently, at the end of that loop,
that variable is an empty string always. Previously, that variable was used
within log output. However, the log output was not changed.
ASTERISK-26915 #close
Change-Id: I09315f31b4d78fb214bb2a9fb6c0f5e143eae990
When receiving a 422 response, the invitestate variable must be reset to
INV_CALLING.
ASTERISK-26841
Change-Id: Ia0502d6b02192664cefa4e75bafdd2645ce56099
* manager.c:manager_state_cb() Fix potential use of uninitialized hint[]
if a hint does not exist for the requested extension. Ran into this when
developing a testsuite test. The AMI event ExtensionStatus came out with
the hint header value containing garbage. The AMI event PresenceStatus
also had the same issue.
* manager.c:action_extensionstate() no need to completely initialize the
hint[]. Only initialize the first element.
* pbx.c:ast_add_hint() Remove unnecessary assignment.
* chan_sip.c: Eliminate an unneeded hint[] local variable. We only care
about the return value of ast_get_hint() there.
Change-Id: Ia9a8786f01f93f1f917200f0a50bead0319af97b
This change fixes a problem where removing the DTLS configuration
options and reloading would not disable DTLS. This occurred
because the DTLS configuration was not reset to an unconfigured
state on reload.
ASTERISK-26313
Change-Id: I10952709cc4a7727fb50534b042bce9d64894b39
* app_minivm: Use built-in completion facilities to complete optional
arguments.
* app_voicemail: Use built-in completion facilities to complete
optional arguments.
* app_confbridge: Add missing colons after 'Usage' text.
* chan_alsa: Use built-in completion facilities to complete optional
arguments.
* chan_sip: Use built-in completion facilities to complete optional
arguments. Add completions for 'load' for 'sip show user', 'sip show
peer', and 'sip qualify peer.'
* chan_skinny: Correct and extend completions for 'skinny reset' and
'skinny show line.'
* func_odbc: Correct completions for 'odbc read' and 'odbc write'
* main/asterisk: Correct and extend completions for 'core show file
version.'
* main/astmm: Use built-in completion facilities to complete arguments
for 'memory' commands.
* main/bridge: Correct completions for 'bridge kick.'
* main/ccss: Use built-in completion facilities to complete arguments
for 'cc cancel' command.
* main/cli: Add 'all' completion for 'channel request hangup.' Correct
completions for 'core set debug channel.' Correct completions for 'core
show calls.'
* main/pbx_app: Remove redundant completions for 'core show
applications.'
* main/pbx_hangup_handler: Remove unused completions for 'core show
hanguphandlers all.'
* res_sorcery_memory_cache: Add completion for 'reload' argument of
'sorcery memory cache stale' and properly implement.
Change-Id: Iee58c7392f6fec34ad9d596109117af87697bbca
We shouldn't unlock the channel after starting a snapshot staging because
another thread may interfere and do its own snapshot staging.
* app_dial.c:dial_exec_full() made hold the channel lock while setting up
the outgoing channel staging. Made hold the channel lock after the called
party answers while updating the caller channel staging.
* chan_sip.c:sip_new() completed the channel staging on off-nominal exit.
Also we need to use ast_hangup() instead of ast_channel_unref() at that
location.
* channel.c:__ast_channel_alloc_ap() added a comment about not needing to
complete the channel snapshot staging on off-nominal exit paths.
* rtp_engine.c:ast_rtp_instance_set_stats_vars() made hold the channel
locks while staging the channels for the stats channel variables.
Change-Id: Iefb6336893163f6447bad65568722ad5d5d8212a
The escalator works by creating a set of startup commands in cli.conf
that set up logger channels and issue the debug commands for the
subsystems specified. If asterisk is running when it is executed,
the same commands will be issued to the running instance. The original
cli.conf is saved before any changes are made and can be restored by
executing '$prog --reset'.
The log output will be stored in...
$astlogdir/message.$uniqueid
$astlogdir/debug.$uniqueid
$astlogdir/dtmf.$uniqueid
$astlogdir/fax.$uniqueid
$astlogdir/security.$uniqueid
$astlogdir/pjsip_history.$uniqueid
$astlogdir/sip_history.$uniqueid
Some minor tweaks were made to chan_sip, and res_pjsip_history
so their history output could be send to a log channel as packets
are captured.
A minor tweak was also made to manager so events are output to verbose
when "manager set debug on" is issued.
Change-Id: I799f8e5013b86dc5282961b27383d134bf09e543
