"Safer" version of ftdm_clamp(), that swaps min/max parameters if
vmin happens to be larger than vmax, making sure the output will
always satisfy vmin <= x <= vmax.
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
The default remains the same: we show the huge ClueCon nag banner on
startup and in fs_cli.
However, if you pass --disable-huge-cluecon-nag, no banner will be
shown.
If you pass --enable-modest-cluecon-nag, a modest text-based ClueCon
reminder will be shown instead.
Some people, it seems, were having sleepless nights from the
log messages this feature produces every 15 minutes.
Default disable the feature, because i hate repeating myself
over and over, explaining them this is a non-issue and intended
behaviour and how to disable it in the config.
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
FTDM_SIGEVENT_UP was falling through to FTDM_SIGEVENT_PROGRESS_MEDIA, which
does (almost) the same, so no harm, but still fix it.
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
Channels can be in DOWN state but reserved by an incoming call
(FTDM_CHANNEL_INUSE flag). Additionally check the flag in on_timeout_t3xx()
and skip those channels.
Reported-by: privi #freetdm @ irc.freenode.net
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
Do not try to send RESTART on BRI PTMP spans, libpri will just print
an error and do nothing, causing the channels to be stuck in RESTART
forever.
Add T316 (RESTART ACK timeout), which is not implemented by libpri.
The default timeout is 30 seconds (Q.931 recommends 2 minutes, but
that is a little long and libpri layer 2 is being stupid) and the
restart attempt limit to 3 (instead of 2).
Periodically send RESTART on idle b-channels in PTP NT mode.
Default interval is 15 minutes, feature can be disabled by setting
"idle_restart_interval" to 0 in the span configuration.
Allow timeout / interval values to have an additional time unit
suffix for convenience reasons, the default (no unit specified)
is milliseconds, valid units include:
w (week), d (day), h (hour), m (minute), s (second)
Only full integers are accepted, no fractional numbers, valid examples:
2w = two weeks
37m = 37 minutes
1h = 1 hour
Combinations of multiple numbers and units (e.g. "1w5d") are not supported.
New span configuration parameters:
idle_restart_interval (milliseconds / time unit suffix /
0 = disabled)
t316 / restart_timeout (milliseconds / time unit suffix)
t316_limit / restart_attempts (number of max. attempts)
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
Add per b-channel private data (ftdm_libpri_b_data_t), move the q.931 libpri
call pointer into it and use channel->call_data to make it accessible.
Use ftdm_channel_wait() instead of select() to wait for I/O events on
the D-Channel and rewrite the timeout handling, adding support for custom
timers that can be added to the b-channel private data and started/stopped
with lpwrap_timer_start()/_stop().
The (sorted) list of active lpwrap timers is protected by the timer_mutex,
which is initialized in the now unified lpwrap_init_pri() (see below) and
destroyed in the new lpwrap_destroy_pri() function.
Unify lpwrap_init_pri() and lpwrap_init_bri(). Use the span type to select
BRI/PRI and Point-to-Point vs. Multipoint settings.
Use the new custom lpwrap timer API to implement T302 (aka overlap receiving
digit timeout). The default T302 timeout is 3000 miliseconds and can be set
via the "digit_timeout" or "t302" span configuration parameter
(0 = disable timer, valid range = 3000 ... 30000 miliseconds).
The lpwrap_pri_init() changes made it neccessarry to rewrite the span runtime
thread event loop. The d-channel initialization and libpri event handler
registration have been moved out of the event loop. The b-channel restart
handling in the event loop has been left as-is, pending a further clean up in
the future.
Rename on_info() to on_information() and add a new on_keypad_digit() event
handler to convert incoming KEYPAD DIGIT messages to channel DTMF events
(only useful on BRI PTMP NT-mode).
The channel restart handling has been improved to distinguish between locally
triggered and restarts caused by the remote end (= incoming RESTART messages).
Restarts on the D-Channel now use pri_restart(), causing a Q.921 reset on
the span.
Large patch, i'd have loved to split this into smaller pieces and actually
test some of the bits more toroughly (restart handling), but some people
are f*cking annoying, so here it is.
Signed-off-by: Stefan Knoblich <stkn@openisdn.net>
AC_PROG_LIBTOOL
m4_include(m4/acinclude.m4)
Adding these and taking out all the Makefile.in files from the tiff-4.0.2
directory seems to sort out the build issues.
Anthony Minessale
Jeff Lenk
Steve Underwood
Seven Du
Stefan Knoblich
David Yat Sin
Robert Jongbloed
Michael Jerris
Travis Cross
Moises Silva
Brian West
Steve Underwood
Nenad Corbic
Moises Silva
Kapil